Once a project has settled on chevron, one decision is still open, and it changes the floor more than most buyers expect: the miter angle. Our Specify page lists chevron with mitered ends at 45° or 30°. Both make a continuous point down each row, but they do not make the same floor. The angle sets how sharp the point is, how wide each row reads, how long the cut end of each block becomes and how strongly the floor pulls the eye. This guide explains those differences in plain geometry, and what to put on the drawing.
What the angle actually measures
A chevron block is a parallelogram. Its two long sides are parallel, and its two ends are cut at the same angle instead of square. A left block and a right block meet along their mitered ends, and that joint line becomes the center line of the row.
In this article, the angle describes the cut at the end of the block, measured between the end cut and the long side. The trade does not always measure it that way. Some drawings measure from the cross line of the room, and some describe the point instead of the cut, so a “60° chevron” in one catalog and a “30° chevron” in another can be the same floor.
This is why we ask for the angle to be shown on the drawing, with the reference line marked, rather than written as a number in an email. Our article on chevron vs herringbone covers the difference between the two patterns; this one goes deeper into the chevron angle itself.
How the angle changes the point
If the end of each block is cut at a given angle to its long side, the two blocks that meet at the center line form a point twice as wide as that angle.
- A 45° cut gives a point of 90 degrees. The point is a right angle, and the blocks run out from the center line at a moderate slope. This is the chevron most people picture.
- A 30° cut gives a point of 60 degrees. The point is sharper, and the blocks lie closer to the direction of the row.
From the doorway, a 45° chevron reads as a broad, even zigzag, and a 30° chevron as a row of narrower arrows with a stronger sense of movement.
How the angle changes the row and the block
The same block width and length behave differently at the two angles.
| 45° cut | 30° cut | |
|---|---|---|
| Point at the center line | Right angle | Sharper, narrower point |
| Direction of the blocks | Moderate slope from the center line | Closer to the line of the row |
| Row width, same block size | Wider | Narrower |
| Length of the mitered end | Shorter | Longer, close to twice the block width |
| Tip of each block | Moderate | Finer and more exposed |
| Visual effect | Even, classic zigzag | Elongated, strongly directional |
The mitered end is longer at 30°. At 45°, the cut end is a little under one and a half times the block width. At 30°, it is close to twice the block width. Every one of those long joints has to close along the center line, so any small error in angle or length shows as a gap or a step running the full length of the room.
The tip is finer at 30°. The sharper the angle, the thinner the wood at the point of each block, and fine tips need careful handling on site. It is one reason to agree the angle with the installer as well as the designer.
How the angle changes the room
The angle works together with block width and length, so the three should be decided as a set.
- Long rooms and corridors. A 30° chevron strengthens the sense of length. It suits a gallery, a hallway or a long living space where the floor is meant to lead the eye.
- Square rooms. A 45° chevron sits more evenly in a room without a strong direction. The zigzag reads across the room as well as along it.
- Wide blocks. A wide block at 30° produces a long cut end and a large point, which can look bold in a small room. Our widths run from 3-1/4” (83mm) to 9-1/4” (235mm) in current production, with other widths from 3” (76mm) to 12” (305mm) made to order.
- Narrow blocks. A narrow block at 45° gives a fine, busy pattern. The same block at 30° gives slender, fast-moving arrows.
How width and length shape the scale of a block pattern is covered for herringbone in herringbone block proportions. The same logic applies to chevron, with the angle added as a third variable.
Center line, direction and borders
Chevron has a hard center line in every row, so setting out is less forgiving than herringbone.
- Point direction. Show which way the points run relative to the main entrance or sight line. A sharper 30° point makes the direction more obvious.
- Center line position. Show where the center line of each row falls, and how it meets a doorway or the center of the room.
- Edges of the field. At the walls, each row ends in a cut triangle. The sharper the angle, the longer those cuts run along the wall. A border can frame the field and hide them.
- Transitions. Show where chevron meets plank or another pattern.
Profile, construction and precision
Our standard profile is Tongue & Groove on all four sides, machined on HOMAG equipment, with square edge available on request. On a chevron block the profile follows the mitered end, so the end joint has to be as accurate as the long side. Consistent width, thickness and angle are what let the center line stay straight. Our article on T&G profile accuracy explains what to check on the profile.
For chevron, 2-layer engineered is the construction most commonly used: a sawn oak wear layer bonded to a stable core, and a practical choice where floor height is limited. Our standard builds are 5/8” (15mm) overall with a 3mm sawn wear layer and 3/4” (20mm) overall with a 6mm sawn wear layer. Other thicknesses from 3/8” (10mm) to 13/16” (21mm) are made to order.
Approving the angle on a sample
A single block does not show the angle. Ask for enough left and right blocks to lay at least one full point, with the center line visible, and look at it from the main entrance in the project’s own light, with the intended color, texture and sheen. Grain direction changes from left to right block, so the two hands can read as slightly different tones under directional light.
The approved sample becomes the master reference, and patterns are shown during dry lay in the factory before packing.
What to put in the RFQ
| Item | What to send |
|---|---|
| Angle | 45° or 30°, drawn, with the reference line marked |
| Block size | Width and length, taken from the drawing |
| Direction | Point direction against the entrance or main sight line |
| Center line | Position in each room, and at doorways |
| Borders | Width and corner detail, if the field is framed |
| Profile | T&G on four sides, or square edge |
| Construction | Build, overall thickness and wear layer |
| Finish | Grade, color reference, texture and sheen |
| Quantity | Sq ft per area, with left and right blocks balanced |
Working with Vu Uy Wood
We manufacture made-to-order solid and engineered French White Oak flooring in Song Than 3 Industrial Park, Ho Chi Minh City, and have done so since 2006, with plank, herringbone, chevron and parquet produced to buyer specification. You can see finished chevron on our Showcase page. Select Chevron as the format on the Specify page and send the drawing with the angle marked; the block size and angle are confirmed at quotation, and the drawing is reviewed together with the specification. We normally reply within one working day.