A hotel floor is specified differently from a floor in a private home. The same build repeats across many rooms, the traffic includes luggage, carts and housekeeping as well as guests, and a damaged area has to be repaired without taking a room out of service for long. Floors are often fitted out in phases, sometimes floor by floor, and the last rooms must look like the first. This article sets out what specifiers and hotel procurement teams weigh when choosing engineered oak, and what to agree with the factory before the order.
Where oak goes in a hotel
Oak is rarely used the same way in every area. The specification is easier to write, and to quote, when it is split by zone.
| Zone | How the floor is used | What to weigh |
|---|---|---|
| Guest rooms and suites | Steady use, luggage, chairs, housekeeping | Repeatable spec, board replacement, sheen under window light |
| Corridors | Concentrated traffic along one path, long sight lines | Texture, low sheen, wear in the center line |
| Lobby, lounge, feature areas | Heavy traffic, high visibility | Format, grade, how the floor meets entrance matting |
| Restaurants and bars | Chairs moved all day, spills | Texture, finish maintenance, replacement planning |
Plank, herringbone and chevron can be combined in one order under the same approved color reference, so a project can use herringbone in a lounge and plank in the rooms without managing two color standards. The decision on where wood stops and another material starts, for example at entrances, belongs to the designer.
Traffic and the build of the board
Traffic decides more of the specification than the color does.
- Construction. 3-layer engineered, with a cross-layered core and backing layer, is well suited to wider boards and larger open areas such as lounges. 2-layer engineered is a practical choice where floor height is limited, which is common in refurbishment of existing buildings, and is commonly used for herringbone and chevron.
- Wear layer. Hotels refurbish on a cycle. A thicker wear layer leaves more oak for future sanding when the rooms are renewed. Our standard builds are 5/8” (15mm) overall with a 3mm sawn wear layer and 3/4” (20mm) overall with a 6mm sawn wear layer, with other builds made to order. The trade-offs are covered in the wear layer guide.
- Grade. Natural and Rustic grades, with visible knots and color movement, are more forgiving of everyday marks than a Premium face, which shows a clean, quiet surface where every mark is visible.
- Texture. A brushed surface breaks up light and tends to disguise fine marks. A smooth surface shows the floor at its cleanest and shows wear soonest. Our range runs from Smooth through Light Wire Brushed, Medium Wire Brushed and Wire Brushed to Wire Brushed with Cross Marks.
These are general observations, not performance claims. How a floor wears in a given hotel depends on the traffic, the cleaning regime and the maintenance program.
Finish and sheen
A prefinished floor arrives with its color and topcoat already UV-cured on the factory line. On a hotel program, that matters for two reasons: rooms can be handed back without a site finishing stage, and every room is finished on the same line against the same master panel. Unfinished boards, supplied sanded for site finishing, remain an option where the hotel has specified a particular site-applied finish system.
Sheen is worth deciding zone by zone. Matte, Extra Matte and Ultra Matte all soften reflections. Lower sheen generally makes scuffs less obvious and keeps glare down in corridors and rooms with large windows, where light rakes across the floor. See Matte, Extra Matte or Ultra Matte for how the three compare.
Maintenance and recoating should follow the guidance for the finish system chosen. Ask for that guidance at quotation so the hotel’s housekeeping and maintenance teams have it before opening.
Repairs: replacing boards, not rooms
In a hotel, a damaged board is a room out of service. Plan for replacement at the specification stage:
- Installation method. Our Tongue & Groove profile is machined on all four sides and is intended for glue-down or nail-down installation. How a single board is cut out and replaced in either method is the installer’s procedure, so ask the installer to describe it before the method is fixed.
- Spare stock. Order spare cartons from the same production lot as the installed floor and store them on site in suitable conditions. The quantity is agreed between the operator and the installer.
- Lot labels. Carton labels identify the SKU and production lot. Keep spare cartons labeled by the area they belong to.
- Later orders. Replacement boards ordered years later are checked against the same retained master panel. The installed floor will have aged by then, so new boards will not look identical to it. Our article on matching a new floor to an existing one covers that situation.
Consistency across floors and phases
Guests walk from room to room and floor to floor. Differences that would go unnoticed in a house become visible along a corridor.
- One master panel. The approved physical sample becomes the master reference. Color is checked against it during production, and texture and sheen are checked across the production lot.
- Lots by area. Ask for production lots to be kept together and labeled so the installer can lay one lot per room or per floor, rather than mixing lots at random.
- Phased deliveries. When fit-out runs floor by floor, later deliveries are checked against the same master as the first.
- Mixed formats. Plank, herringbone and wider boards can be produced under the same approved color standard.
Documentation specifiers ask for
Hotel procurement usually needs paperwork that a residential buyer does not ask for. Agree the list at quotation:
| Document | Purpose |
|---|---|
| Written specification with reference | The basis of the quotation and the sample |
| Approved sample record | The appearance standard for production and inspection |
| CARB Phase 2 documentation for the composite core | Formaldehyde emissions, for U.S. projects |
| Finish system and maintenance guidance | For the hotel’s housekeeping and maintenance teams |
| Packing list with SKU and lot per carton | Receiving, storage and spare stock |
If the project has code requirements for floor finishes in public areas, state them in the RFQ so they can be reviewed at quotation. Do not assume them from a standard product sheet. For writing the full specification, see specifying flooring for a project tender.
Specifier checklist for a hotel
- Zones listed separately, each with format, width and quantity in sq ft
- Construction and wear layer chosen for traffic and the refurbishment cycle
- Grade and texture chosen with wear visibility in mind
- Sheen set per zone, approved on a sample under the project’s light
- Finish system and maintenance guidance agreed
- Installation method and board replacement procedure confirmed by the installer
- Spare stock from the same lot, labeled by area
- Lots kept together by room or floor
- Document list agreed at quotation
Working with Vu Uy Wood
We manufacture solid and engineered French White Oak flooring to buyer specification in Song Than 3 Industrial Park, Ho Chi Minh City, and have done so since 2006, with U.S. residential and hospitality projects among our completed work. Finishing is done on our own UV line, and the approved panel is kept as the master reference for later phases and replacement orders. You can see installed floors on our completed work page and set out each zone on the Specify page. We normally reply within one working day.