Wood changes size with the moisture in the air around it, so a wood floor cannot be fixed hard against every wall and still stay flat. The answer is a clear space left around the edges of the floor and at anything that rises from it, then hidden under trim. It is called an expansion gap, expansion space or perimeter gap, and it is one of the details that most often goes missing from drawings. This guide explains what the gap is, where it goes, how it is covered and who decides its size. It is general information; the installer and the project’s installation guidance decide the details. Our guide to installation method and the specification shows how the method shapes the order.
What the gap is
The National Wood Flooring Association (NWFA) glossary defines it as a space necessary between fixed objects, for example the walls of a room, pipes and cabinets, and the wood flooring itself, to allow the flooring system to move. Its trim chapter describes baseboard and base shoe as the mouldings that cover the perimeter expansion space where the floor meets the wall. The reference is NWFA’s Wood Flooring Installation Guidelines, revised 2025.
Moisture is the reason. Wood takes up moisture and swells, mainly across the grain, and gives it up and shrinks. Our article on seasonal movement of solid oak explains the mechanism. The gap gives the swelling floor somewhere to go.
Where it goes
| Location | What the guidelines say |
|---|---|
| Wall lines | Expansion space is left between the flooring and the wall; baseboard covers it |
| Cabinets, steps | Base shoe conceals the space between the flooring and the wall, cabinets or steps |
| Pipes and other vertical obstructions | Space is left at every vertical obstruction |
| Door casings and jambs | Undercut so the flooring can slide beneath |
| Doorways (floating floors) | Transition pieces, anchored to the subfloor and not to the flooring |
| Stone fireplaces, staircase stringers, outlets, abutting floor coverings | Where baseboard or shoe cannot be fitted, undercut the abutting material or use an overlapping transition |
The NWFA text also warns about the opposite problem. A floating floor should never be installed where future fixed cabinetry, such as a kitchen island, would lock it down, because those are fixed vertical obstructions. Heavy furniture and appliances such as pianos or pool tables can affect the way a floating floor moves, and the guidelines advise telling the end user before product selection or installation. See our guide to floating T&G engineered floors for how that method handles the perimeter.
How it is hidden
The gap is a working part of the floor, not a flaw to be filled. The usual covers are:
- Baseboard, which protects the wall and covers the perimeter space where the floor meets it.
- Base shoe or quarter round, a narrower moulding used with or instead of baseboard to complete the cover.
- T-moulding, reducers and baby thresholds, used at doorways and around hearths. The NWFA text says an overlap reducer or T-moulding should not be fastened to the wood flooring; it is attached only to the subfloor so the space stays open.
For floating floors, the guidelines go further: baseboard, shoe and quarter round must not touch the floor and should never be fastened to or through the flooring system. Trim fixings go into the wall.
Who sets the size
There is no single number for every floor. The NWFA text for nail-down, glue-down and floating methods says, in different words, to keep proper expansion space at all vertical obstructions, based on the material being installed, and gives a general figure tied to the thickness of the flooring unless the flooring manufacturer directs otherwise. The same text says transitions and extra spacing within the floor may be needed on wide spans, depending on the species, climate, interior climate control and time of year. For solid wood the guidelines describe working out expected change from the width of the board, the species’ dimensional change coefficient and the expected change in moisture content.
In practice the decision is shared:
| Who | Decides |
|---|---|
| Flooring manufacturer | Any size or span rule specific to its product; given in writing on request |
| Adhesive or underlayment maker | Limits for its system, where one is used |
| Installer | The size on site, set with spacers, and where transitions are built in |
| Architect or specifier | Details that leave the space and cover it: trim, thresholds, door casings, fixed joinery |
| General contractor | The order of trades, for example baseboard fitted after the flooring |
The flooring factory makes the boards to the agreed specification. It does not stand on your site, so the gap is not something we set for you; it is set by the installer against the installation guidance, and we can confirm what the board construction needs at quotation.
Common mistakes
- Drawing the floor flush to the wall. A detail with no gap and no trim leaves the installer to improvise.
- Fastening trim through the floor. For floating floors in particular, nails through baseboard or thresholds into the flooring can stop the floor from moving.
- Fixed joinery built on top of the floor. Cabinets set on a floating floor lock it. Fit them to the subfloor and finish the floor around them.
- Forgetting existing elements. Hearths, stringers, outlets and abutting floor coverings need their own detail.
- Treating one number as universal. The gap depends on the product and the method.
What to write in a specification
- State the installation method (nail-down, glue-down or floating) and refer to the installation guidance the project follows, such as the NWFA guidelines.
- Ask the flooring manufacturer for any expansion or span requirement for the board and method in writing, before installation starts.
- Show the trim and transition details on the drawings: baseboard and shoe at walls, thresholds at doorways, overlap at hearths and stringers.
- List fixed objects the installer must treat as vertical obstructions, including planned cabinetry.
- Say who checks the gaps before the trim goes on.
Working with Vu Uy Wood
Vu Uy Wood manufactures made-to-order solid and engineered French White Oak flooring in Song Than 3 Industrial Park, Ho Chi Minh City, and has done so since 2006. Tell us the installation method on the Specify page together with the board construction and width you want, and ask for any requirement tied to the board at quotation. Our guide to installation method and the specification lists what to include. We normally reply within one working day.