A drawing tells a factory more about a floor than any product name. It shows where the herringbone turns, how wide the border is, how the stair nosing meets the landing and which rooms share a color. It also shows what is missing. Before a floor drawn by an architect or designer can be quoted, someone has to turn it into a list of pieces that can be cut, profiled, finished and packed. This article explains what we check when a flooring drawing arrives, the questions we typically send back, and what is confirmed in the quotation.
What a drawing review is for
The review has one job: to make sure every piece in the drawing can be built as drawn, and that nothing the price depends on has been left to assumption. It is not a site survey and it does not replace the installer’s setting-out. Responsibilities stay where they belong:
- The designer owns the design: pattern, proportions, borders and where they sit.
- The installer owns the site: final measurements, subfloor, method and setting-out.
- The factory owns the pieces: their sizes, construction, profile and finish, made consistently across the order.
At Vu Uy Wood, a drawing is reviewed together with the specification, which is why it is best sent with the first request rather than after a quote.
Check 1: Units and dimensions
The first pass is about numbers.
- Units. Imperial or metric, and whether both appear. Where a drawing mixes them, we ask which one governs.
- Scale. Whether the drawing is to scale, and whether the dimensions or the scale should be trusted if they disagree.
- Face width. Whether a stated board or block width is the visible face or the overall piece including the tongue.
- Room sizes and piece sizes. Room dimensions set quantities; piece dimensions set machining. Both are needed, and they are read separately.
- “Verify on site” notes. Any dimension marked for site verification is flagged, because it can change the piece list.
Check 2: Pattern geometry
Each pattern has its own critical dimensions.
- Herringbone. Block width and one fixed block length for the whole order, left and right blocks, and the direction of the pattern against a main wall or sight line.
- Chevron. The angle, 45° or 30°, the block width, and where the points fall in the room.
- Parquet. The shape and size of every piece, how pieces repeat, and grain direction within each unit.
- Panels. For a Versailles or other panel floor, the panel size and the pieces that make up each panel.
A pattern name alone rarely settles these points. Our article on chevron vs herringbone geometry explains why the drawing governs.
Check 3: Borders and frames
Borders are where drawings most often leave gaps.
- Border width, and whether it is one piece or several bands.
- Corner detail: mitered, butted, or a separate corner block.
- Grain direction in the border relative to the field.
- How the field meets the border, and whether the field is cut to the border on site.
- Whether the border is a different grade, color or texture from the field.
For parquet with borders, our guide to custom parquet from drawings goes into the piece detail.
Check 4: Stairs and edges
Stairs and floor edges are drawn at a smaller scale than rooms, so details are easy to miss.
- Tread depth and length, and the number of treads of each size.
- Nosing profile, and whether risers, landings and moldings are included.
- Where the floor meets the stair, and at what height.
- Thresholds and transitions to other floor finishes.
Stair parts are matched to the floor in color and finish and approved on a sample. See oak stair treads that match the floor.
Check 5: Construction and profile across areas
Where two areas meet, their builds have to work together.
- Thickness at transitions. A herringbone hall meeting a plank living room should normally share an overall thickness, or the drawing should show how the height difference is handled.
- Construction per area. Solid, 2-layer or 3-layer, chosen with the subfloor and method for each area.
- Profile per piece type. T&G on four sides, or square edge, and any micro-bevel.
- Installation method per area, as confirmed by the installer.
Check 6: Color and finish per area
The drawing should say which color, texture and sheen go where. More than one format can be produced within one order using the same approved color reference, so a single master can cover a whole project. Where a drawing uses different tones in a field and a border, each tone needs its own reference and its own sample.
Check 7: Quantities
Quantities are read from the drawing by area and by piece type, in sq ft for floor areas and by count for stair parts and special pieces. The waste allowance for cutting and setting-out is the installer’s call; we ask who set it and on what basis, so it is applied the same way to every piece type, including both hands of a herringbone.
Items that are not flooring
Architect sets often show doors, cabinetry and built-in joinery next to the floor. Flooring is made in our own factory. Furniture, cabinetry and doors can be coordinated through our vendor network of partner workshops, and the quotation states clearly which items come from which source. The arrangement is described in flooring and joinery project supply.
Questions we typically send back
| What the drawing shows | Question sent back |
|---|---|
| “Herringbone, 5 inch” | Is 5” (127mm) the face width, and what is the block length? |
| “Chevron” with no angle | 45° or 30°, and where should the first point fall? |
| A border with no corner detail | Mitered, butted, or a corner block? |
| Plank and herringbone in adjacent rooms | Same overall thickness, or a transition detail? |
| Stairs on plan only | Tread depth, nosing profile, and are risers included? |
| One color named for the whole floor | Does the border share the field color, texture and sheen? |
| Total area only | Quantity per area and per piece type? |
| Dimensions marked “verify on site” | Who confirms them, and before which stage? |
Answering these once, in writing, saves a round of questions and makes the first sample more useful.
What the quotation confirms
When the review is complete, the quotation states what will be built:
- Piece sizes for each format, block and border element
- Construction, overall thickness and wear layer for each area
- Profile and edge detail for each piece type
- Pattern details: block length, chevron angle, panel size, as applicable
- Color, texture, sheen and finish system, with the sample plan
- Quantities by area and piece type
- Any assumptions made, and any items not included
Custom pieces are made to drawing, confirmed at quotation. If the drawing is revised after that, send the revision with its number so the change can be reviewed against the confirmed version.
Before you send a drawing
- A dimensioned PDF, plus CAD files if you have them
- Units stated, and which dimensions govern
- Pattern direction shown against a wall or sight line
- Border and corner details drawn at a readable scale
- Stair sections, if stairs are included
- Color, texture and sheen marked per area
- The specification for each area, from construction to finish
Working with Vu Uy Wood
Vu Uy Wood manufactures solid and engineered French White Oak flooring to buyer specification in Song Than 3 Industrial Park, Ho Chi Minh City, and has done so since 2006, with herringbone, chevron, plank and parquet produced to drawing. Build your written specification on the Specify page and attach your drawings through the contact page; for projects that also include doors or cabinetry, see Project Supply. Drawings are reviewed together with the specification, and we normally reply within one working day.