Light reflectance value, or LRV, is a single number for how much visible light a surface reflects. Architects and accessibility consultants use it to check that a floor and the walls or doors beside it can be told apart, and lighting designers use it to estimate how much light a room will give back. It turns up in specifications for hotels, healthcare and public buildings, and a buyer of wood flooring may be asked for it. This guide explains what the number is, how it is measured and what changes on a real oak floor. The short version: it is read on the finished, approved sample, which is why our guide to approving color on a physical sample applies here too.
What LRV is
LRV describes the amount of light a surface reflects. SATRA explains the scale in its guidance on LRV this way: a value of 100 represents total reflectance of light, so the surface looks white, and a value of 0 represents total absorption, so it looks black. Wikipedia describes LRV as a ratio of reflected light to total light, not an absolute amount of reflected energy. In practice, a surface is rated on how much of the light that falls on it comes back.
Two points follow:
- It is a brightness number, not a color name. A warm brown and a cool gray can share the same LRV. It says nothing about undertone.
- It describes the surface, not the room. The room’s lighting, window size and furnishings are separate.
How it is measured
The method most often named is BS 8493:2008+A1:2010, the British Standard test method for the light reflectance value of a surface. SATRA states that it uses CIE Y, x, y values measured under standard conditions with a sphere-type spectrophotometer. The Y value is the luminance in the CIE 1931 color model. EN 17317:2020 adapts the BS 8493 method for floor coverings, so ask the testing laboratory which standard applies to a finished wood board.
SATRA lists three ways to get a number:
| Method | Accuracy | Note |
|---|---|---|
| Sphere-type spectrophotometer to BS 8493 | Laboratory method | Lab test on a sample; SATRA gives the minimum sample size for general surfaces as 450 mm x 450 mm (about 17-3/4” x 17-3/4”) |
| Hand-held colorimeter | Approximate | Suited to on-site use; may be unsuitable for glossy surfaces |
| Visual match to swatches of known LRV | Least accurate | Affected by the lighting, which should be recorded |
Why a wood floor is harder to read than a paint chip
A paint chip is flat and even. A wood floor is not, and four things change the reading.
Grain and board variation. SATRA notes that a spectrophotometer result is accurate only at the point measured. Oak carries grain figure, density and color that differ from board to board, so one reading describes one spot. For a floor, agree where on the sample the reading is taken, or take several and state how they are combined.
Surface texture. SATRA states that BS 8493 applies to opaque materials with surface texture under 2 mm (about 5/64”). Brushing opens the grain, and deeper brushing means a more textured surface. If the texture you specify is deep, ask the laboratory whether the method suits the sample.
Gloss. SATRA says shiny or matt surfaces affect the judgement of contrast, and that colorimeters may be unsuitable for glossy surfaces. Sheen is set by the topcoat, so read the LRV on a board with the production finish and sheen, never on bare wood. Our guide to measuring floor sheen explains how gloss itself is measured.
Finish and age. The reading is taken at one moment. SATRA points out that a spectrophotometer result does not account for fading from weathering or for the effects of installation, such as lighting. A reading on a new sample is a starting figure.
Where specifications use LRV
The common use is contrast. SATRA cites guidance that adjacent surfaces where contrast matters should generally differ by 30 points or more, and Wikipedia gives the same 30-point figure for BS 8300:2018. SATRA adds that a difference of 20 points may be acceptable for large areas or rooms above 200 lux, and that under 20 points is considered poor. These come from accessibility guidance for people with reduced eyesight, for example at doors, stair edges and floor changes.
A worked example, with invented numbers for illustration only and not measured from any floor: if a wall is read at 60 and the floor at 30, the difference is 30 points. If the floor were read at 40, the difference would be 20 points. Which level a project needs comes from its accessibility consultant and the local rules, not from the flooring factory.
This is why the reading matters when a floor is chosen. A pale floor and a pale wall can fail a contrast check even when the two colors look different on a screen.
What we do and do not publish
Our color library lists color names and codes. It does not list LRV values, and we do not give a figure for a color from memory or from a photograph. The only reliable figure is one read on the approved sample, with the finish, texture and sheen of the order. If a project needs it, say so when you request the quotation, and ask whether the reading can be arranged; it is confirmed at quotation and on an approved sample. Do not take an LRV from one color and apply it to another that looks similar.
Writing LRV into a specification
- Name the standard. For example BS 8493, or the test method the project names.
- State the sample. The approved sample, with production finish, texture and sheen.
- State the measurement. Where on the sample, how many readings and how they are combined.
- Name who measures. A laboratory, or the supplier with a report, agreed in advance.
- Set the tolerance in points, agreed between buyer, specifier and supplier.
- Keep the sample. The approved panel is the master for production, so later boards can be compared with it.
Lighting still decides how it looks
A good LRV does not guarantee how a floor looks in the finished room. Daylight, interior lighting and the color of the surfaces around the floor all change what the eye sees. Review the approved boards in the project’s light. Our guide to white and cream oak floors shows how lighting changes a pale floor, and the same applies at the dark end of the library.
Working with Vu Uy Wood
Vu Uy Wood manufactures made-to-order solid and engineered French White Oak flooring in Song Than 3 Industrial Park, Ho Chi Minh City, and has done so since 2006. If your project asks for a light reflectance value, send the requirement with your selections on the Specify page, together with the standard it names, and we will review it against the sample, as set out in our guide to approving color on a physical sample. We normally reply within one working day.