Color & Finish

Hardwood Floor Finish Types Compared: Lacquer, Oil, Polyurethane

Hardwood floor finish types compared: UV lacquer, UV oil, hardwax oil, natural oil, waterborne and oil-modified polyurethane, with advantages and limits.

Vu Uy Wood · November 21, 2026
All buyer guides
Living room with a light finished wood floor and soft daylight
Photo: Julia on Unsplash

The finish is the part of a hardwood floor that the owner lives with every day. It sets the look of the oak, how spills behave, how the floor is cleaned and what a repair involves years later. Yet in many specifications it is reduced to one word, “lacquered” or “oiled”, when there are at least six distinct finish types in common use, each with its own advantages and limits. This article sorts them into two families, compares them side by side, and explains where each one fits, so a buyer or specifier can choose on how the floor will actually be used.

Two questions that sort every finish

Before comparing products, ask two questions.

Does the finish form a film, or does it penetrate? A film finish sits on top of the wood as a continuous clear layer and seals the grain. A penetrating finish soaks into the top fibers and hardens there, leaving the grain open and little or nothing on the surface. Film finishes generally resist stains better and need less routine care. Penetrating finishes are easier to repair locally and keep a more natural feel.

Is it applied in a factory or on site? A factory finish is applied and cured on a line before the boards are packed, so the floor is finished when it arrives. A site finish is applied after installation, so the color and sheen are set in the room by the finisher. Some finish types exist only in one setting; others are used in both.

The six finish types side by side

FinishFamilyUsually appliedLookMain advantagesMain limits
UV-cured lacquerFilmFactory lineClear, even surface in a range of sheensCured before packing, even across a lot, low routine careLocal repair can show; recoat needs a compatible product
UV oilPenetrating, UV-curedFactory lineNatural, open grainFactory-cured oil look, floor usable on arrivalOngoing oil maintenance; less stain resistance than a film
Hardwax oilPenetrating, with waxFactory or siteSoft, natural, low sheenEasy spot repair, blends with existing finishRegular maintenance; liquids can mark if left
Natural oilPenetratingMostly siteWarm, deepens the wood toneSimple to renew, very natural feelSlow to cure, frequent care, warms over time
Waterborne polyurethaneFilmMostly siteClear, stays close to the raw wood toneFaster drying, milder odor, little amberingCan look flat on oak if not tinted; product quality varies widely
Oil-modified polyurethaneFilmSiteAmber, warms with ageTough film, familiar to finishersAmbers over time, slow drying, strong odor during application

The table describes the finish types in general terms. Performance depends on the specific product, how it is applied and how the floor is maintained, so the maker’s data and the finisher’s experience govern the details.

Film finishes

UV-cured lacquer

A UV-cured lacquer hardens under ultraviolet lamps rather than drying slowly in air. On a finishing line, stain and topcoat are applied and cured in sequence, so each layer is fixed before the next goes on. The result is a consistent film across a production lot, a floor that is ready for use when installed, and a surface that needs only routine cleaning. The limit is repair: a scratch through the film shows as a pale line, and blending a patch is harder than re-oiling. Our article on UV-cured finishes describes the line sequence.

Some factory topcoats include aluminum oxide particles as a wear additive. It can improve resistance to abrasion, and it can make later recoating more demanding. If it matters to your maintenance plan, ask the supplier whether the topcoat contains it.

Waterborne polyurethane

The common choice for finishing unfinished oak on site. It dries faster and smells less than solvent-based products, and it stays close to the raw color of the wood, which suits pale and raw-look colors. On oak, some waterborne products can react with the wood’s tannin, so test on a board first. Two-component versions with a crosslinker are often chosen for commercial traffic.

Oil-modified polyurethane

The traditional site-applied film. It builds a tough coat and gives oak a warm amber tone that deepens with age. That warmth is the main reason to choose it, and the main reason to avoid it on pale or neutral color schemes. It dries slowly, and the room has to be ventilated and kept clear while it cures. Our article on waterborne vs oil-based polyurethane compares the two site finishes.

Penetrating finishes

UV oil

An oil formulated to be cured under UV lamps on a factory line. It gives the open-grain look of an oiled floor with the convenience of a factory finish. Most makers recommend a maintenance oil after installation and at intervals afterwards, so the owner should receive the care routine with the floor.

Hardwax oil

A blend of natural oils and waxes that hardens inside the top fibers. It is applied in factories and on site. Its strength is local repair: a worn patch can be cleaned and re-oiled, and the new oil blends with the old. Its cost is regular upkeep. See UV oil vs hardwax oil for how the two oil routes differ.

Natural oil

Plain penetrating oils give the warmest, most traditional look. They cure slowly, need the most frequent maintenance, and tend to warm the tone of oak over time. They suit owners who enjoy caring for a floor and want it to age visibly.

Sheen across finish types

Film finishes are made in a wide range of sheens, from very low matte through to gloss. Penetrating finishes usually sit at the low end, because there is little film to reflect light. Sheen is measured with a gloss meter, commonly at a 60 degree geometry under ISO 2813 or ASTM D523, but sheen names are not standardized between makers, so the approved sample is the reference that matters.

Which finish suits which project

ProjectFinish types to considerReason
Fast-track fit-out, occupied buildingUV-cured lacquerFinished on arrival, no site coating
Private home, owner wants a natural feelHardwax oil, UV oilEasy local repair, open grain
Hotel, retail, managed maintenanceUV-cured lacquer, waterborne polyurethaneLow routine care, even look
Pale or raw-look color schemeUV lacquer at low sheen, waterborne polyurethaneLittle ambering
Traditional warm oak toneOil-modified polyurethane, natural oilWarmth that deepens with age

For a closer look at care and repair across the two families, see oiled vs lacquered oak flooring.

What we produce

Our finishing routes are Clear UV, Color UV and Color and Effect UV, with stain and topcoat applied and UV-cured on our own finishing line, in Matte, Extra Matte or Ultra Matte. Unfinished boards are also supplied sanded and ready for site-applied finishing, which is the route for a site-applied polyurethane or oil; the finish maker and finisher then decide the product and method. If your project needs a factory oil or another finish type, ask whether it can be produced; it is confirmed at quotation and on an approved sample.

Questions to ask any supplier

Working with Vu Uy Wood

Vu Uy Wood manufactures made-to-order solid and engineered French White Oak flooring in Song Than 3 Industrial Park, Ho Chi Minh City, and has done so since 2006. Finish system, sheen and texture are chosen together on the Specify page, and the Production page shows the UV finishing line where stain and topcoat are cured. We normally reply within one working day.

More in Color & Finish

Related guides

Your project

Build the floor around your specification

Construction, format, width, grade, color, texture and finish are set per order. Work through the options, or send us the floor you are trying to match.

WhatsApp Request a quote