“Matte” on one data sheet and “matte” on another can describe two different floors. Sheen names are words chosen by each coating maker, and words do not travel well between suppliers, between markets or between an order and its reorder. A gloss meter gives sheen a number, which helps, but only if both sides know how the number was taken and what it can and cannot tell them. This article explains what a gloss meter measures, the standard geometries, why a reading on oak is harder than a reading on a test panel, and how to write sheen into a specification so that buyer and factory check the same thing.
What a gloss meter measures
A gloss meter shines a beam of light onto the surface at a fixed angle and measures how much light comes back at the mirror angle on the other side. This is the specular reflection, the part of the light that makes a window visible in a floor. Light scattered in other directions is not counted.
The result is given in gloss units (GU). A gloss unit is not a percentage of light reflected. It is a comparison with a polished black glass reference standard, which sets the top of the scale for each geometry. A surface that reflects like that glass reads at the top of the scale, and a surface that scatters nearly everything reads close to zero. Background on the optics is on Wikipedia’s gloss article.
A meter is only as reliable as its calibration. Before readings are taken, it is checked against its own reference tile, and the tile has to be clean and undamaged.
The standards and the 60° geometry
Two standards are cited most often for the specular gloss of coatings: ISO 2813 and ASTM D523. They describe the same principle and the same family of measuring angles, each angle being measured from a line perpendicular to the surface.
- The 60° geometry is the general-purpose angle. It is used for most coatings and is the usual starting point for any reading.
- A geometry closer to vertical is used for high-gloss surfaces, where the 60° reading crowds together near the top of the scale and stops separating one surface from another.
- A near-grazing geometry is used for very low-sheen surfaces, where the 60° reading crowds together near the bottom of the scale.
The standards give guidance on when to move from 60° to one of the other angles. For flooring, the consequence is simple: a gloss number without its geometry means nothing. A reading at 60° and a reading at a near-grazing angle from the same board are different numbers, and comparing them is comparing two different measurements.
Why sheen names differ between makers
Each coating maker draws its own boundaries between matte, satin and the rest. Those boundaries are set by the maker’s product range, not by a shared table. As a result:
- One maker’s matte can read like another maker’s extra matte.
- Satin covers a wide band, and two satins can look clearly different side by side.
- The same product can read differently on a smooth test panel than on a wood floor.
- Reorders from a different coating batch, or a change of product, can move the reading even when the name on the label stays the same.
So a sheen name on a data sheet describes a family, not a value. Our article on hardwood floor sheen levels describes how each family looks in a room.
Why a reading on oak is harder than on a test panel
Coating makers usually measure gloss on a flat, smooth, uniform test panel. A wood floor is none of those things.
| Factor | Effect on the reading | What to do |
|---|---|---|
| Open oak grain | The film follows the pores, and readings vary across a board | Take several readings and use the average |
| Grain direction | Readings along the grain and across it can differ | Measure in one agreed direction |
| Wire brushing | Relief scatters light, readings drop and spread widely | Rely on visual comparison with the sample |
| Bevels and board edges | The meter window sits partly off the flat face | Measure in the center of the face |
| Dust, packing residue, fingerprints | Lower or uneven readings | Clean the surface as agreed before measuring |
| Color | The meter reads reflection, but the eye sees sheen more on dark colors | Judge appearance on the sample, not the number alone |
The textured surfaces deserve a special note. On a Light Wire Brushed board, a meter can still give useful readings with care. On deeper brushing, and on Wire Brushed with Cross Marks, the meter window may sit on a ridge in one place and a groove in the next, and the readings say more about the texture than about the finish. For those surfaces, the approved physical sample is the only reference that works. Our article on Matte, Extra Matte or Ultra Matte explains how texture and sheen interact.
What a gloss number can and cannot tell you
A reading is good at answering narrow questions:
- Are two boards from the same finish system at the same sheen?
- Has a production lot moved away from the approved sample?
- Do two coating products, measured the same way on the same substrate, sit close together?
It cannot tell you how the floor will look in the room. The eye also responds to haze, to how sharp the reflected image is, to the viewing angle, the light and the color, and a single gloss reading captures none of these. Two floors with the same reading can look different, and two floors that look the same can read apart.
Writing sheen into the specification
The approved physical sample is the primary reference. A gloss reading, if one is wanted, supports the sample. It does not replace it. A practical specification line looks like this:
- “Sheen: Extra Matte, as the approved sample.”
If the buyer needs a measured value as well, the specification should say how it is taken:
- Standard and geometry. For example, ISO 2813 or ASTM D523, 60° geometry.
- Where it is measured. On the face of the approved sample and of production boards, in the center of the face, along the grain.
- How many readings. Several readings per board on several boards, averaged.
- The reference value. Read from the approved sample itself, not copied from a coating data sheet.
- The acceptable range. Agreed at sample stage, before production, by both sides.
Never take a value from another supplier’s data sheet and apply it to a new floor. It was measured on a different product, on a different surface, possibly at a different angle.
Checking sheen at inspection and on delivery
- Compare boards against the retained sample under the same light, from a low angle as well as from above.
- If a meter is used, use a calibrated meter, the agreed geometry and the agreed method, on clean boards.
- On brushed surfaces, make the visual comparison the deciding check.
- Record the result together with color and texture checks.
The wider inspection routine is covered in our article on pre-shipment inspection of hardwood flooring.
How sheen is handled at Vu Uy Wood
We produce three sheens on our UV finishing line: Matte, Extra Matte and Ultra Matte. The topcoat is applied at a controlled film weight and UV-cured in line, and surface inspection checks texture and sheen across the production lot against the approved sample, which becomes the master reference. If your specification calls for a gloss reading as well, raise it at quotation; how the readings are taken and recorded is agreed then and tied to the approved sample.
Working with Vu Uy Wood
Vu Uy Wood manufactures made-to-order solid and engineered French White Oak flooring in Song Than 3 Industrial Park, Ho Chi Minh City, and has done so since 2006. Sheen, texture and finish system are set together on the Specify page, and any measurement requirement can be added to your request on the Contact page. We normally reply within one working day.