A floating floor is not fixed to the subfloor. It rests on an underlayment, and everything the owner feels underfoot passes through that layer: how firm the floor is, how it sounds, how it handles small dips in the subfloor and, over concrete, how it deals with moisture from below. The underlayment is often bought last and chosen on price. For an engineered oak floor it deserves the same attention as the board. This article compares the common types, explains what changes when a tongue and groove floor is floated with glued joints, and sets out who should confirm each choice.
How a floating T&G oak floor works
In a floating installation, the boards are joined to each other and not to the subfloor. With a tongue and groove profile, the installer applies a joint adhesive into the groove along the sides and ends, so the floor bonds into one continuous panel. That panel rests on the underlayment, with an expansion gap left at the walls and at fixed objects, so the whole floor can move slightly as indoor conditions change.
Three consequences follow for the underlayment:
- It carries the floor. Every footstep and every piece of furniture loads the underlay through the board. If the underlay compresses too much, the joints flex.
- It must not grip the floor. The panel has to move over it freely. Anything that pins the floor, such as fixed cabinets or a heavy island fastened through it, defeats the method.
- It sits in the moisture path. Over concrete, the underlay or a film beneath it is the floor’s moisture control.
Our Tongue & Groove profile is machined on all four sides and is intended for glue-down or nail-down installation. If a floating installation is being considered, raise it before the specification is fixed, so the installer, the buyer and the factory can agree that the board and method suit each other. The method itself is covered in floating installation of T&G engineered oak.
The main underlayment types
Foam
Polyethylene and similar foams are the most common underlays. They are light, easy to lay and economical. Denser foams resist compression better than soft ones. Foam gives modest sound reduction and only bridges very small irregularities in the subfloor. Many foam products are sold with a film attached for use over concrete.
Rubber
Recycled or synthetic rubber underlays are heavy and dense. They reduce impact sound well and resist long-term compression, which is why they are often chosen for apartments. Check that the rubber product is approved by its maker for floating wood floors, since some rubber layers are designed for glued floors only.
Cork
Cork is a natural material that recovers well after compression and gives good impact sound reduction. It is firm underfoot. Over concrete it usually needs a separate film beneath it, unless the product includes one.
Felt and fiber
Felt and fiber underlays are made from recycled textile or wood fibers. They are firm, they help smooth minor surface texture and they give a solid feel. Their behavior over a damp slab must be checked with the maker, and a film below them is usually needed over concrete.
Combined vapor and acoustic underlays
Many products combine a sound-reducing layer with an attached film, so a single roll does both jobs. They save a step, but the film side must face the right way and the seams must be sealed as the maker describes.
Comparison at a glance
| Type | Underfoot feel | Impact sound | Resistance to compression | Over concrete |
|---|---|---|---|---|
| Foam | Softer | Modest | Varies with density | Needs film, often attached |
| Rubber | Firm, dense | Good | Good | Check the maker’s approval |
| Cork | Firm | Good | Good recovery | Usually needs separate film |
| Felt and fiber | Firm | Moderate | Good | Needs film |
| Combined vapor and acoustic | Depends on core | Depends on core | Depends on core | Film included |
Why softer is not better
It is tempting to choose the thickest, softest underlay on the shelf for comfort and sound. Under a glued T&G floating floor, that can work against the floor. A soft underlay lets the boards move down under a load and come back up when it is removed. Over time, that movement stresses the glued joints, which can open gaps or make the floor feel springy and sound hollow.
A firmer underlay of moderate thickness generally supports the joints better. The underlay maker states which thicknesses and densities are approved for floating wood floors, and the installer matches them to the board. A sample board laid on the intended underlay shows how the combination feels and sounds before the whole order is made.
Sound in multi-family buildings
In apartments, the underlay is usually chosen to meet a building’s impact sound requirement. Ratings belong to the complete assembly, the structure, ceiling, underlay and floor, not to the board or the underlay alone. Ask the building for its requirement in writing and the underlay maker for a test report on a similar assembly. Our article on acoustic underlay for apartments explains how the ratings work.
Moisture over concrete
Over a slab, a polyethylene film is laid below the underlay, or comes attached to it, with seams overlapped and taped and edges turned up at the walls. The film does not replace testing the slab; the installer still tests it and confirms it is ready. Over a wood subfloor, the installer decides whether a film is appropriate for the climate and the building. Our article on vapor retarders under wood flooring explains where these layers go for each method.
Radiant heating
An underlay adds thermal resistance between the heating and the floor. If the floor is heated, the heating system maker should approve the underlay, and the underlay maker should confirm it is suitable for heated floors.
Choosing the board for a floating floor
The board and the underlay work together:
- Construction. A floating floor depends on its own stability, since nothing holds it down. A 3-layer board, with a cross-layered core and a backing layer, is well suited to wider boards and larger open areas. See the installation method guide for how construction and method relate.
- Thickness. A thicker board spreads load across the underlay better. Our standard builds are 5/8” (15mm) and 3/4” (20mm) overall, with other thicknesses from 3/8” (10mm) to 13/16” (21mm) made to order.
- Width and run length. Wide boards and long uninterrupted runs move more as a panel. The installer and the joint adhesive maker set the limits for room size and transitions.
Who confirms what
| Decision | Who confirms it |
|---|---|
| Whether floating suits the board | Installer and factory, before the specification |
| Underlay type and thickness | Underlay maker’s approval, chosen by the installer |
| Joint adhesive | Adhesive maker, applied by the installer |
| Film over concrete | Installer, after testing the slab |
| Sound requirement | Building, with the underlay maker’s test data |
Working with Vu Uy Wood
Vu Uy Wood manufactures made-to-order solid and engineered French White Oak flooring in Song Than 3 Industrial Park, Ho Chi Minh City, and has done so since 2006. If a floating installation is planned, tell us the underlay and subfloor along with your selections on the Specify page, or describe the project on the contact page, so the board and method are agreed before the specification is fixed. We normally reply within one working day.