Every finished wood floor wears, and the finish decides how it is brought back. A lacquered floor is renewed by abrading and recoating its film. An oiled floor is renewed by cleaning it and adding oil. Both sound simple until a new coat fails to stick, a repair shows as a patch, or the recoat leaves the floor at a different sheen. This article covers the maintenance cycle for each finish, how a screen and recoat works, when a spot repair is realistic and why a compatibility test comes before any recoat. Our comparison of oiled vs lacquered oak flooring deals with choosing the finish; this one deals with keeping it going. In every case, the finish maker’s instructions govern the products, the preparation and the curing.
The maintenance cycle, stage by stage
Both finishes follow the same broad cycle. What changes is the work done at each stage.
| Stage | Lacquered (film) floor | Oiled floor |
|---|---|---|
| Routine cleaning | Dry sweep, then a lightly damp mop with a cleaner approved for the finish | Cleaner or soap made for oiled floors |
| Periodic refresh | A maintenance product, where the finish maker recommends one | Maintenance oil or refresher as the surface starts to look dry |
| Recoat | Light abrasion and a new topcoat while the film is still intact | Deep clean, light abrasion where needed, and a new coat of oil |
| Spot repair | Limited, and the patch can show | Usually practical and blends well |
| Full refinish | Sanding to bare wood within the wear layer, then a new finish | The same |
The move from one stage to the next is decided by looking at the floor, not by a date. A lacquered floor is ready for a recoat when traffic paths look dull and finely scratched but the film is still whole. Once bare, pale wood shows through, a recoat alone is no longer enough. An oiled floor is ready for attention when the surface looks dry, marks more easily and liquids darken the wood quickly instead of sitting on top.
Screen and recoat on a lacquered floor
A screen and recoat renews the film without sanding into the wood. The usual sequence is:
- Identify the existing finish. Factory UV coating, site-applied waterborne finish or oil-modified finish: the answer decides which products can go on top.
- Deep clean. Remove grime and, above all, any residue of polishes, waxes or silicone-based products. Contamination of this kind is a common reason a recoat peels.
- Abrade lightly. The surface is screened or buffed with a fine abrasive so the new coat has something to grip. The aim is to dull the film evenly, not to cut into the wood.
- Remove all dust. Vacuum and tack the surface as the finish maker directs.
- Apply the new topcoat. Use a product the maker approves over the existing finish, at the sheen you want the floor to have.
- Let it cure. Keep traffic, rugs and furniture off for as long as the maker states.
Factory UV coatings are hard and dense, which is part of why they wear well. It also means a site-applied coat needs thorough abrasion and a product that its maker approves for use over UV-cured finishes. Some makers supply a bonding primer for this purpose.
Two side effects to plan for. First, the new coat sets the sheen, so recoating a Matte floor with a satin product changes the whole floor. Our guide to hardwood floor sheen levels explains why that difference shows. Second, a recoat keeps a wire-brushed texture, while full sanding removes it. The wear layer guide covers how recoating and sanding relate to the thickness of the oak.
Re-oiling an oiled floor
An oiled floor is maintained more often but with lighter work. After cleaning with a product made for oiled floors, maintenance oil is applied thinly and the excess is buffed off, so that nothing is left sitting on the surface. Where wear is heavier, the area is lightly abraded first and then re-oiled.
On a color-oiled floor, ask the oil maker whether the maintenance oil should be clear or tinted, because a mismatch slowly shifts the color in the areas that are maintained most. And follow the maker’s instructions on disposing of used rags and pads: cloths soaked in drying oils can heat up on their own as they cure.
Spot repair: what is realistic
| Damage | Lacquered floor | Oiled floor |
|---|---|---|
| Fine scratches in the finish only | Maintenance product, or a recoat of the area | Local re-oil |
| Scratch through the film to the wood | Color touch-up, then a local coat; often better to recoat to a natural break | Abrade locally and re-oil; usually blends |
| Deep gouge or a stain in the wood | Sand the board, or replace it | Sand locally and re-oil, or replace the board |
| Water damage at the joints | Replace the affected boards | Replace the affected boards |
On a lacquered floor, a patch of new coating on one spot often shows as a slightly different sheen. Recoating to a natural break, such as a doorway, a threshold or the edge of a room, hides the join.
For damage that goes into the wood, board replacement is the clean answer. On a tongue and groove floor, a skilled installer can cut out a damaged board and fit a new one. That depends on having spare boards from the original delivery, stored flat inside the building, because a later production lot will not match exactly.
Compatibility testing before any recoat
A recoat that does not bond has to come off again. Before treating the whole floor:
- Find out what is on the floor. Check the handover documents and maintenance records, or ask the flooring supplier for the finish system.
- Make a test patch in a hidden area, such as a closet or under a fixed piece of furniture. Prepare it exactly as planned, apply the product and let it cure fully.
- Check adhesion. A common site check is to press tape firmly over the cured test area and pull it off sharply. If the new coat lifts, stop and ask the finish maker.
- Check the look. Compare color and sheen of the test patch with the rest of the floor.
Oil and lacquer do not mix. A lacquer will not bond reliably over an oiled floor, and an oil cannot soak through an intact film. Changing from one system to the other usually means sanding back to bare wood.
Who decides
The finish maker decides which products, preparation and cure times are acceptable. The installer or floor finisher decides the method on site and carries out the test patch. The flooring supplier provides the name of the finish system and its care guidance. Keep all of it in the building’s handover pack.
Vu Uy Wood finishes and their maintenance
Our three prefinished routes, Clear UV, Color UV, and Color and Effect UV, are UV-cured film finishes applied on our own line, so for maintenance they behave in the manner of a lacquer. On Color UV and Color and Effect UV floors the color stain sits beneath the topcoat, so a recoat in good time protects the color; once traffic wears through the film, the color in that area is hard to restore without sanding. Maintenance and recoating should follow the guidance for the finish system chosen, and that guidance can be requested at quotation. The UV-cured finish article describes how the coating is built.
For an oiled floor, order the Unfinished route and have the oil applied on site. A factory-oiled finish is not one of our listed routes; ask whether it can be produced, and it is confirmed at quotation and on an approved sample.
Working with Vu Uy Wood
Vu Uy Wood manufactures made-to-order solid and engineered French White Oak flooring in Song Than 3 Industrial Park, Ho Chi Minh City, and has done so since 2006. Finish system, sheen and texture are set on the Specify page, and care guidance for the chosen finish can be requested with your quotation. We normally reply within one working day.