Specification & Construction

Taber Abrasion Test for Oak Floor Finishes Explained

Taber abrasion test for oak floor finishes explained: how the test works, what the numbers mean, what it cannot predict and how to ask for results in an RFQ.

Vu Uy Wood · November 21, 2026
All buyer guides
Used abrasive sanding bands and sawdust lying on a wooden workbench, illustrating abrasive wear on wood

When a project specification asks for the Taber abrasion result of a floor finish, the request is usually a line copied from a coatings standard, and the answer is usually a number with no context. Buyers receive a figure, compare it with another supplier’s figure and conclude one floor is tougher than the other. Sometimes that is right. Often the two numbers were produced under different conditions and cannot be compared at all. This guide explains what the Taber test does, how to read a report and how to ask for results that mean something.

Diagram: Taber Abrasion Test for oak floor finishes explained

What the test is

The Taber abraser is a laboratory machine. A flat specimen is fixed to a turntable, and two abrasive wheels rest on its surface under a set load. The table turns, the wheels drag across the specimen, and the surface is worn in a circular track. The test runs for a set number of cycles, or until the coating is worn through to the layer below.

The method most often named for coatings is ASTM D4060, which covers the abrasion resistance of organic coatings using this machine. The standard sets out the equipment and the procedure, and leaves the choice of wheel, load and cycle count to be stated for each test. That last point is the one buyers miss. A result is only meaningful with its conditions attached.

What a result looks like

A Taber result is reported in one of two ways.

Both are reported with the wheel type, the load and, for mass loss, the number of cycles. Common wheels are the milder CS-10 and the more aggressive CS-17, and loads are set in grams. Change any of the three, and the number changes.

Report fieldWhy it matters
Standard and editionFixes the method used
Wheel typeMore aggressive wheels wear a coating faster
Load on each wheelHeavier loads wear faster
Number of cyclesMass loss depends on the run length
Unit of resultMass loss and cycles cannot be compared
Specimen descriptionFinish system, sheen, color and substrate
Laboratory and dateWho ran it and when

If a report leaves out any of these, it cannot be used to compare floors.

What the test tells you

The Taber test measures how well a coating resists abrasive wear in a controlled setting. That is a real property, and it is relevant to a floor, where grit carried on shoes wears the finish over time.

It is useful for three comparisons.

In each case, the comparison only holds when the test conditions are identical.

What the test does not tell you

A flooring buyer should keep the limits in view.

For these reasons the abrasion result is one input to a specification and not the whole of it.

What affects the result

Several choices in the finish system change an abrasion result.

A result for a clear finish on a smooth sample says little about a dark stain with a wire brushed texture, because the topcoat sits at different depths on the surface.

How a test fits a project

Taber results are most useful when written into the process, not asked for at the end.

  1. Decide whether the project needs it. Retail, hospitality and public areas often do. A private residence rarely does.
  2. State the standard and the conditions in the RFQ. Name the method, the wheel, the load and the cycles, or ask the supplier to propose conditions and report them.
  3. Ask for the test on your finish system. That means the same stain, topcoat, sheen and texture, on oak.
  4. Agree what is passed. A pass or fail line should be written before testing, not afterwards.
  5. Check a lot against the master. The approved sample becomes the reference for production.

Common misreadings

Three habits cause most of the confusion around abrasion figures.

When a supplier sends a figure, the first step is to ask for the full report, not the headline number. A report with the conditions attached can be compared. A number without them is a claim.

Using a test requirement in a tender

A specifier who wants an abrasion requirement in a tender should write it as a method and a limit, for example the standard, the wheel, the load, the cycles and the maximum mass loss, and should allow bidders to submit an equivalent. Writing only a number invites bids that meet it under easier conditions. Writing the method keeps every bid on the same footing and makes the lot check at delivery straightforward. Our article on writing a flooring specification for tenders shows where such a line sits in the document.

What we say about our finishes

Our finish routes are Unfinished, Clear UV, Color UV and Color and Effect UV. Stain and topcoat are applied on our UV finishing line, with process settings controlled to support consistency within a production lot and across repeat orders. We do not publish a Taber figure on this page, because a figure without a method, a wheel and a finish system is not useful. If your project needs an abrasion result, put the standard in the RFQ. Whether a report exists for your finish system, or a test will be run on the approved sample, is confirmed at quotation.

Questions to ask any supplier

QuestionA clear answer covers
Which standard, wheel, load and cycles?Conditions you can repeat
Was the specimen the same finish system?Stain, topcoat, sheen and texture
Which laboratory ran it, and when?An independent record
Is the substrate oak?A relevant face
What does production check against?The approved sample as master

Working with Vu Uy Wood

Vu Uy Wood manufactures solid and engineered French White Oak flooring to buyer specification in Song Than 3 Industrial Park, Ho Chi Minh City, and has done so since 2006. Finish, sheen and texture are chosen on the Specify page, and any test requirement can be written into the quotation. We normally reply within one working day.

More in Specification & Construction

Related guides

Your project

Build the floor around your specification

Construction, format, width, grade, color, texture and finish are set per order. Work through the options, or send us the floor you are trying to match.

WhatsApp Request a quote